Zanussi
Zanussi Washing Machine Door Seal8071200029
Suitable for Zanussi, AEG, Electrolux, Elektro Helios, Faure
Stock Code: 672428
·
£27.15inc. VAT
£22.63 ex. VAT
In Stock
Next Day Delivery Available
Moderate DIY repair
A confident home repairer can do this with basic tools.
01
Compatibility Check
02
What this part does
Creates a watertight seal between the drum and the door.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| E30 | AEG | Means water has been detected in the bottom tray and the anti flood system has tripped, or a fault with the water pressure sensor. It is usually caused by leaks, over sudsing, or laundry trapped in the door seal. | Medium |
| E40 | AEG | Means a door locking fault, where the door is not fully closed, the seal is obstructed, or the door lock mechanism is faulty. It is usually caused by a door not closing properly or a faulty door lock. | High |
| E41 | AEG | Means the door or lid is not closed properly, the machine is overloaded, or the door lock mechanism is faulty, with the control board detecting the door switch open. It is usually caused by a door not closing properly, overloading, or a faulty door lock. | High |
| EF0 | AEG | Means a water system fault, with water accumulating in the bottom tray. It is usually caused by too much detergent, a dirty dispenser, or a leak. | High |
| EF3 | AEG | Means a water sensor fault relating to water ingress and a failure to reset after flooding. It is usually caused by a leaking door seal that is damaged or cracked. | High |
| C3 | Electrolux | Means a flood or water has been detected in the bottom tray, often with 3 beeps. It is usually caused by a leaking seal, a clogged drain filter, excessive suds, or laundry trapped in the door seal. | High |
| E13 | Electrolux | Means there is a water leak into the base pan, or the water level drops below the required point during operation. It is usually caused by a slow leak, over-sudsing, or a faulty pressure sensor or switch. | High |
| E44 | Electrolux | Means the machine cannot detect that the door is properly closed and locked. It is usually caused by trapped laundry, a damaged door seal, a faulty door lock mechanism, or a faulty main board. | High |
| EF0 | Electrolux | Means a flood safety condition has been triggered. It is usually caused by excessive suds, a clogged drain filter, an internal water leak, or a leaking door seal. | High |
| E13 | Zanussi | Means an internal water leak has triggered the anti-flood device in the base of the machine. It is usually caused by a drain pump fault, a split hose, or a loose seal. | Medium |
| E42 | Zanussi | Means a door lock malfunction, specifically a problem with the door aperture closure mechanism. It is usually caused by damage or debris on the door lock assembly, with the same fault family covering E43 door interlock triac, E44 door closure sensing circuit, and E45 triac sensing circuit. | High |
| EF0 | Zanussi | Means the anti-flood system has been activated with water detected in the base tray, also reported as EFo or EF3. It is usually caused by excessive foam from over-soaping, a clogged drain filter, or a minor leak. | High |
| EF3 | Zanussi | Means the Aqua Control system has detected a water leak and activated safety mode. It is usually caused by over-sudsing, a damaged door seal, a filter blockage, or a leak into the base tray. | High |
E30Medium
AEG
Means water has been detected in the bottom tray and the anti flood system has tripped, or a fault with the water pressure sensor. It is usually caused by leaks, over sudsing, or laundry trapped in the door seal.
E40High
AEG
Means a door locking fault, where the door is not fully closed, the seal is obstructed, or the door lock mechanism is faulty. It is usually caused by a door not closing properly or a faulty door lock.
E41High
AEG
Means the door or lid is not closed properly, the machine is overloaded, or the door lock mechanism is faulty, with the control board detecting the door switch open. It is usually caused by a door not closing properly, overloading, or a faulty door lock.
EF0High
AEG
Means a water system fault, with water accumulating in the bottom tray. It is usually caused by too much detergent, a dirty dispenser, or a leak.
EF3High
AEG
Means a water sensor fault relating to water ingress and a failure to reset after flooding. It is usually caused by a leaking door seal that is damaged or cracked.
C3High
Electrolux
Means a flood or water has been detected in the bottom tray, often with 3 beeps. It is usually caused by a leaking seal, a clogged drain filter, excessive suds, or laundry trapped in the door seal.
E13High
Electrolux
Means there is a water leak into the base pan, or the water level drops below the required point during operation. It is usually caused by a slow leak, over-sudsing, or a faulty pressure sensor or switch.
E44High
Electrolux
Means the machine cannot detect that the door is properly closed and locked. It is usually caused by trapped laundry, a damaged door seal, a faulty door lock mechanism, or a faulty main board.
EF0High
Electrolux
Means a flood safety condition has been triggered. It is usually caused by excessive suds, a clogged drain filter, an internal water leak, or a leaking door seal.
E13Medium
Zanussi
Means an internal water leak has triggered the anti-flood device in the base of the machine. It is usually caused by a drain pump fault, a split hose, or a loose seal.
E42High
Zanussi
Means a door lock malfunction, specifically a problem with the door aperture closure mechanism. It is usually caused by damage or debris on the door lock assembly, with the same fault family covering E43 door interlock triac, E44 door closure sensing circuit, and E45 triac sensing circuit.
EF0High
Zanussi
Means the anti-flood system has been activated with water detected in the base tray, also reported as EFo or EF3. It is usually caused by excessive foam from over-soaping, a clogged drain filter, or a minor leak.
EF3High
Zanussi
Means the Aqua Control system has detected a water leak and activated safety mode. It is usually caused by over-sudsing, a damaged door seal, a filter blockage, or a leak into the base tray.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
MediumGeneral fitting guidance. The exact steps can vary slightly with the make and model of your washing machine.
Safety: Switch off and unplug at the mains before you start.
You’ll needFlat screwdriver
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
06
Specifications
- Part Number
- 8071200029
- Alternative Part Numbers
- 8071200011
- EAN / Barcode
- 7321423189169
- Genuine Spare Part
- Yes
07
More Details
This is a genuine door seal for your washer door.
Seals the space between the drum and outer casing of your washing machine to keep water, detergent, and suds safely contained during every cycle. It also cushions the door as it closes, reducing noise and preventing direct metal contact.
If you’re noticing leaks, rust stains, or unusual noise during washes, your existing seal could be damaged. Replace it with this part to restore proper function and peace of mind.
This door seal for your washing machine is from Zanussi. It also fits AEG, Electrolux, Elektro Helios, Frigidaire, John Lewis, Novamatic, Rex, Rosenlew, and Zanker models.
Before ordering, please verify that this part fits your model using our compatibility checker.
08
Customer Reviews (5)
5.05 reviews
5
5
4
0
3
0
2
0
1
0
Door seal
Item as described. Fitted perfectly. No complaints. Quick delivery too.
Bruce Thomson · Dundee ·
Quality
Value
Ease of Fitting
The seal of doom
Fair delivery, it was a pain to fit myself but after few go’s i eventually got it Great product , great business can’t fault them.. I just never want to fit a washing machine door seal again! Thank you
Joely jones · Conwy ·
Quality
Value
Ease of Fitting
Great product
Washing machine seal - arrived quickly, good condition and excellent value for money compared to other sellers.
Steve Pye · Milton Keynes ·
Quality
Value
Ease of Fitting
Does what you'd expect
A perfect like for like seal that's done its job beautifully. Fitting takes a but of effort - but that's how it should be to enable a good tight seal. Fits perfectly - the actual fitting (after dismantling the machine) took less than 15 mins.
Rob Miles · Peterborough ·
Quality
Value
Ease of Fitting
Great product, hard to fit!
Arrived on time, good quality part. Only problem was fitting the inner wire/spring. We, two of us, eventually turned machine on its back which allowed a bit more room to stretch the inner wire/spring into place. Marvellous what a bit of perseverance can achieve!
David G · Tewkesbury ·
Quality
Value
Ease of Fitting
09
Questions & Answers (1)
do I need a trained AEG engineer to fit this product
Anita · London ·
Hi Anita, you won't usually need an engineer to fit this. I'd recommend watching a video on youtube to give you an idea of what work needs to be undertaken.
JordanStaff·