Next Day Delivery Available
Will This Part Fit My Appliance?
This is a universal part - please check details / specifications for suitability with your model.
Description
What does a washing machine drain pump do?
The dirty water in the washing machine is removed by a washing machine drain pump and put into the drain hose or plumbing system. The machine's drain cycle initiates the drain pump, which is normally found at the bottom of the device.
What causes a faulty drain pump?
Blockages brought on by accumulated dirt and wear and tear from repeated use may lead to a malfunctioning washing machine drain pump. Electrical difficulties like poor wiring or loose connections, foreign objects getting into the pump, and issues with the motor like burned-out coils or mechanical failures all result in obstructions.
These problems can impair water flow, lessen pump performance, and cause poor drainage or drain pump failure.
How do you replace a damaged drain pump?
Check our tutorial video below on how to replace a washing machine drain pump.
This washing machine drain pump is a universal washing machine spare part. It will fit most commercial washing machines.
How to Replace a Hotpoint Washing Machine Drain Pump Askoll
Please note that the following video will give you a guide on how to fit this part, however the exact fitting may differ depending on your make and model.
Safety Warning - Always unplug from the mains before carrying out any repairs.
- Washing machine model used - Hotpoint NSWF 743U W UK N
- Part number used - RS121784
Need to find a specific part of the video? Use the timestamps below...
- 0:22 - Removing existing drain pump
- 0:44 - Installing new drain pump
Specification:
- Universal high performance Askoll Drain Pump (Seperate spade connectors).
- This high quality replacement pump replaces all askoll/plaset drain pumps that have 3-screw pump housing.
Manufacturers Part Number:
- PMP214
Alternative Part Numbers:
- EP-01
- LG33
- N03
- P01
- PMP214
- UN-03
EAN Number:
- 05030017702142
Will this part fit your appliance?
Use our compatibility checker, Click here.
Finding your model number:
Struggling to find the model number on your Washing Machine? Click here.
Safety note:
Warning: Always unplug any appliance from the electricity supply before carrying out any work or testing on it.
Latest Product Review(s)
Keeping the old Zanussi WDT 1085 running
The drain pump failed on the old Zanussi, but an Askol replacement from Ransom Spares soon had it operational again. While the machine is a bit like 'Trigger's brush' to keep it working for £10 ish is ano brainer. Easy to fit , 3 screws, although I had to cut off the old plug from the wiring loom and solder on two new spade terminals, 5 min job. Delivery was fast, no problems.
Easy replacement for AEG
Fairly easy replacement for pump on AEG Lavamat 72600 (from 1997) with c2 error code. Wiring loom doesn't fit so needs adapter or just a get a couple of spade connectors as I did.
AEG Washing machine pump
Good value generic pump, easy to fit after much dismantling of the washing machine to gain access.
Great replacement
Pump works exactly as it should, albeit a little bit noisier than the original. Extremely easy to install although I would recommend ordering the adapter kit to fit wiring harness
Saved £300 and repaired the machine.
So disconnect the power. Simply drop the pump down. Remove 3 philips screws Refit with new part.
Quality easy fit Pump
Quick delivery, quality compatible pump, I had to replace the existing pump connecting plug with Crimp Spade connectors ( few minutes,highlighted on the product description.) New pump works well. Highly recommended.
Had To Make Some Adjustments
The product is a universal part, even though I entered the correct model number online. The existing water pump body has 'male' pick up points. With this product it has male pick up points also, therefore, it was male to male. To get it to fit, I carefully sawed off the 3 pick up points, carefully drilled 3 holes in the pump body. The rubber 'O' ring fitted nice and tight in the body. I then 'belt and braced' things by putting silicone on the mating surfaces and screwed the pump and body together with 3 self tapping screws. There are holes already in the pump body. I then had to adjust the wiring, as has been mentioned by others. The live and neutral is marked on the pump. And the washing machine pump power feed is marked on my machine, so no problems. And touch wood all is working fine. A satisfactory cheap fix.
Perfect
Great product and nice price. Easy to replace part in my Candy washing machine. Just has to split the 2 pin electrical connector in order to connect to this pump.
Perfect spare part
The drain pump was easy to fit, works perfectly, and was a lot cheaper than some on other sites. Very pleased.
Excellent
Very happy with the product, working as good as any good brand same pump were listed on very high price as compared to this. Very happy with the purchase saved lot of money