Hotpoint
Hotpoint Washing Machine 2-Way Cold Water Inlet ValveC00110333
Suitable for Hotpoint, Ariston, Bauknecht, Ignis, Indesit
Stock Code: 978
·
£9.30inc. VAT
£7.75 ex. VAT
In Stock
Next Day Delivery Available
Moderate DIY repair
A confident home repairer can do this with basic tools.
01
Compatibility Check
02
What this part does
Controls the water flowing into the machine.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| A9 | Indesit | Means a water inlet problem, where the machine is not receiving water or not filling sufficiently. It is usually caused by a water inlet fault, a jammed filter, or an open or short circuit on the main wash triac affecting motor control. | High |
| E1 | Indesit | Means a water intake failure, where the machine cannot detect enough water in the drum within the allotted time. It is usually caused by a water inlet fault, a valve not closing, or a door lock issue. | High |
| F8 | Whirlpool | Means the washer is not detecting the correct amount of incoming water as F8 E1 or Lo FL, while the F08 variant means the heater relay is not being activated. It is usually caused by a water inlet fault, a faulty pressure sensor, a faulty heater relay, or loose module connections. | High |
| F8E1 | Whirlpool | Means a long fill or no fill fault where the washer is not detecting enough water entering the tub, also shown as LoFL. It is usually caused by low water pressure, kinked hoses, or clogged inlet screens. | High |
A9High
Indesit
Means a water inlet problem, where the machine is not receiving water or not filling sufficiently. It is usually caused by a water inlet fault, a jammed filter, or an open or short circuit on the main wash triac affecting motor control.
E1High
Indesit
Means a water intake failure, where the machine cannot detect enough water in the drum within the allotted time. It is usually caused by a water inlet fault, a valve not closing, or a door lock issue.
F8High
Whirlpool
Means the washer is not detecting the correct amount of incoming water as F8 E1 or Lo FL, while the F08 variant means the heater relay is not being activated. It is usually caused by a water inlet fault, a faulty pressure sensor, a faulty heater relay, or loose module connections.
F8E1High
Whirlpool
Means a long fill or no fill fault where the washer is not detecting enough water entering the tub, also shown as LoFL. It is usually caused by low water pressure, kinked hoses, or clogged inlet screens.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
MediumGeneral fitting guidance. The exact steps can vary slightly with the make and model of your washing machine.
Safety: Switch off at the mains and turn off the water supply before you start.
You’ll needScrewdriverPliersTowel
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
06
Specifications
- Part Number
- C00110333
- Alternative Part Numbers
- 481010906666, C00097023, C00097260, C00097792
- EAN / Barcode
- 8052476103336
- Genuine Spare Part
- Yes
07
More Details
What is a cold water inlet valve?
Water inlet valves regulate the flow of both cold and hot water into the washer as well as balance the temperature of the washer's water.
Is there a difference between hot and cold water valves?
The two are identical except for how they work. The clockwise rotation activates the cold side stem. While the hot side would activate by spinning in the opposite direction. You can use a stem with a hot side on a cold side and vice versa.
How do you know if your washing machine’s water inlet valve is broken?
One indication is a complete lack of water flow into the machine during the wash cycle, even when the water supply is turned on. Another symptom is a slow or insufficient water supply, where the machine doesn't receive an adequate amount of water to properly fill the tub.
A malfunctioning inlet valve may also cause leakage or dripping from the valve itself.
Is it easy to replace?
Yes. Watch our tutorial video below on how to fit a washing machine cold water inlet valve.
This cold water inlet valve is a genuine Indesit washing machine spare part. It also fits Ariston, Hotpoint, Scholtes, and Whirlpool washing machines.
08
Video
How to Fit a Washing Machine Cold Fill Inlet Water Valve 2 Way
If you need to replace the cold fill inlet water valve 2 way on your Hotpoint washing machine, we've got the video for you.
The following DIY repair video should assist you in fitting this part. However, the exact procedure may differ depending on your make and model.
Appliance and Part Number:
- Washing machine model used - Hotpoint NSWM743UWUK
- Part number used - RS978
Need to find a specific part of the video? Use the timestamps below...
- 0:21- Removing washing machine lid
- 0:28 - Removing existing water valve
- 0:54 - Removing control panel fascia
- 1:26 - Installing new water valve
09
Customer Reviews (13)
5.013 reviews
5
13
4
0
3
0
2
0
1
0
Sort by:||
Inlet valve
Perfect fit for Hotpoint Whirlpool 7kg washer. Easy to fit. In fact identical to faulty one being removed. Job done in less than 15 mins. Washer back in service.
Jeremy Searle · Brierly hill ·
Quality
Value
Ease of Fitting
5 Star
5 Star Service all the way. Great Service. Part arrived when stated. Good Quality at a reasonable price.
Jane Burns · Middlesbrough ·
Quality
Value
Ease of Fitting
Exact match
The part was an exact match for the faulty one being replaced, very simple to fit and working fine, only issue was the delivery. I paid for next day delivery but it took two days, in fairness the extra postage charge was refunded immediately after I complained
Alan ian Smitheringale · Stockton-on-Tees ·
Quality
Value
Ease of Fitting
Great product
Easy to fit. Customer service was good, delivered in a few days despite the postal strikes.
James · Lancaster ·
Quality
Value
Ease of Fitting
Perfect Fit
Excellent took me 10 minutes to fit came in a Whirlpool bag so I believe it to be a manufacturers part. I had next day delivery - was a gamble on my part getting the correct bit as next step was a new machine. So glad Ransomes saved the day!
Nigel Taylor · Hounslow ·
Quality
Value
Ease of Fitting
10
Questions & Answers (1)
Hi is this inlet valve come with rubber seals Or can you buy seals separatley
Noel · Northern Ireland ·
Hi Noel, I have checked the part and no O-rings are supplied with the item. Can you please send your full model number to us via our part type enquiry form https://www.ransomspares.co.uk/contact/part.htm so that we can find you the O-rings
SamStaff·