Whirlpool
Whirlpool Tumble Dryer Drain Hose480112101508
Suitable for Whirlpool, Bauknecht, Hotpoint, Ignis, Laden
Stock Code: 589509
£20.40inc. VAT
£17.00 ex. VAT
In Stock
Next Day Delivery Available
Easy DIY repair
Most customers complete this swap with basic tools in a few minutes.
01
Compatibility Check
02
What this part does
Carries the condensed water from the dryer to an outside drain.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| F11 | Hotpoint | Means a pump circuit fault, where the pump is disconnected, blocked, or faulty and water is not pumping out. It is usually caused by an open circuit in the pump system. | High |
| F4 | Hotpoint | Means the pump is running when it should not be, suggesting a water drainage problem or a heater circuit fault. It is usually caused by moisture causing a short circuit in the pump circuit, or a clogged pump filter preventing proper drainage. | High |
| F5 | Hotpoint | Means a drainage problem where the pump is not working or a blockage is preventing water from draining. It is usually caused by a blocked filter, a clogged waste pipe, or a failed pump. | High |
| H20 | Hotpoint | Means a water drainage problem, signalling that the condenser water reservoir is full or that draining has failed. It is usually caused by a blocked drain pump, a blocked filter, debris accumulation, or a malfunctioning sensor. | High |
F11High
Hotpoint
Means a pump circuit fault, where the pump is disconnected, blocked, or faulty and water is not pumping out. It is usually caused by an open circuit in the pump system.
F4High
Hotpoint
Means the pump is running when it should not be, suggesting a water drainage problem or a heater circuit fault. It is usually caused by moisture causing a short circuit in the pump circuit, or a clogged pump filter preventing proper drainage.
F5High
Hotpoint
Means a drainage problem where the pump is not working or a blockage is preventing water from draining. It is usually caused by a blocked filter, a clogged waste pipe, or a failed pump.
H20High
Hotpoint
Means a water drainage problem, signalling that the condenser water reservoir is full or that draining has failed. It is usually caused by a blocked drain pump, a blocked filter, debris accumulation, or a malfunctioning sensor.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
EasyGeneral fitting guidance. The exact steps can vary slightly with the make and model of your tumble dryer.
Safety: Switch off and unplug at the mains before you start.
- 1
- 2
- 3
- 4
- 5
- 6
06
Specifications
- Part Number
- 480112101508
- Alternative Part Numbers
- C00314859
- EAN / Barcode
- 8058331148597
- Genuine Spare Part
- Yes
07
More Details
A genuine tumble dryer drain hose. It's a flexible plastic hose with fittings and clamps at both ends to fit with the dryer and plumbing layout.
When you're done drying the clothes, the drain hose extracts wastewater. That collected wastewater then flows into the home's or laundry's drainage system.
If your hose becomes tattered, worn out, or gets leaks, you need to replace it. Change it with this part.
This drain hose is from Whirlpool. It also fits Bauknecht, Hotpoint, Ignis, Laden, Maytag, Miostar (migros), Privileg, and V zug tumble dryers.
Before ordering, please verify with our compatibility checker that this part is suitable for your model.
08
Customer Reviews (1)
5.01 review
5
1
4
0
3
0
2
0
1
0
Easy replacement
Arrived on time as stated and a very easy to fit replacement.
Michael Cowsley · Preston ·
Quality
Value
Ease of Fitting