AEG
AEG Tumble Dryer Fluff Filter8588074539012
Suitable for AEG, Chef, Electrolux, Elektro Helios, Faure
Stock Code: 672752
£20.25inc. VAT
£16.88 ex. VAT
In Stock
Next Day Delivery Available
Easy DIY repair
Most customers complete this swap with basic tools in a few minutes.
01
Compatibility Check
02
What this part does
Traps fluff and lint from the air so it does not block the dryer.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| E52 | AEG | Means the motor overheating safety cut out has been triggered, stopping the cycle or the drum. It is usually caused by a worn motor carbon brush, a faulty motor, a faulty control board, or restricted airflow. | Medium |
| EF1 | Electrolux | Means there is a ventilation blockage or insufficient airflow so the dryer cannot exhaust hot air properly and overheats. It is usually caused by blocked filters or restricted airflow that makes the unit stop to prevent a fire hazard. | High |
| C2 | Zanussi | Means the machine is unable to empty water from the condenser unit, frequently displayed alongside E20 or E21. It is usually caused by a clogged filter, a kinked drain hose, or a faulty drain pump. | High |
| E20 | Zanussi | Means the appliance is unable to remove water effectively, also encountered on washer dryer models with two beeps or flashes. It is usually caused by a pump or drainage fault, a clogged filter, a kinked drain hose, or a lint blockage. | High |
| E21 | Zanussi | Means a water drainage issue or a blocked condensate pump, with the dryer stopping for safety because water is not being removed efficiently. It is usually caused by a blocked filter, a clogged condenser unit, a kinked drain hose, or debris in the pump. | High |
| E32 | Zanussi | Means a fault with the moisture sensor system, where the conductivity sensor signal frequency is too low. It is usually caused by a clogged filter, dirty moisture sensors, or faulty wiring or control board. | High |
| E52 | Zanussi | Means a motor circuit fault or motor overheating, with the control board no longer detecting movement from the motor. It is usually caused by worn carbon brushes, a failed tacho coil, or a faulty motor. | Medium |
| E60 | Zanussi | Means a general heating fault, with the dryer not heating up, taking too long to dry, or leaving the clothes wet. It is usually caused by poor airflow from blocked filters, a tripped thermal safety thermostat, or a faulty heating element. | High |
E52Medium
AEG
Means the motor overheating safety cut out has been triggered, stopping the cycle or the drum. It is usually caused by a worn motor carbon brush, a faulty motor, a faulty control board, or restricted airflow.
EF1High
Electrolux
Means there is a ventilation blockage or insufficient airflow so the dryer cannot exhaust hot air properly and overheats. It is usually caused by blocked filters or restricted airflow that makes the unit stop to prevent a fire hazard.
C2High
Zanussi
Means the machine is unable to empty water from the condenser unit, frequently displayed alongside E20 or E21. It is usually caused by a clogged filter, a kinked drain hose, or a faulty drain pump.
E20High
Zanussi
Means the appliance is unable to remove water effectively, also encountered on washer dryer models with two beeps or flashes. It is usually caused by a pump or drainage fault, a clogged filter, a kinked drain hose, or a lint blockage.
E21High
Zanussi
Means a water drainage issue or a blocked condensate pump, with the dryer stopping for safety because water is not being removed efficiently. It is usually caused by a blocked filter, a clogged condenser unit, a kinked drain hose, or debris in the pump.
E32High
Zanussi
Means a fault with the moisture sensor system, where the conductivity sensor signal frequency is too low. It is usually caused by a clogged filter, dirty moisture sensors, or faulty wiring or control board.
E52Medium
Zanussi
Means a motor circuit fault or motor overheating, with the control board no longer detecting movement from the motor. It is usually caused by worn carbon brushes, a failed tacho coil, or a faulty motor.
E60High
Zanussi
Means a general heating fault, with the dryer not heating up, taking too long to dry, or leaving the clothes wet. It is usually caused by poor airflow from blocked filters, a tripped thermal safety thermostat, or a faulty heating element.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
EasyGeneral fitting guidance. The exact steps can vary slightly with the make and model of your tumble dryer.
- 1
- 2
- 3
- 4
- 5
06
Specifications
- Part Number
- 8588074539012
- Alternative Part Numbers
- 8074539019
- EAN / Barcode
- 7321423120483
- Genuine Spare Part
- Yes
07
More Details
This is a genuine tumble dryer fluff filter.
In a dryer, a fluff filter collects lint, fibres, and other material left over from wet clothing. It helps in avoiding system blockage and recirculation of debris into the dryer drum.
If you see any rips, tears, or holes in the mesh, lint can pass through, and your filter isn’t as effective when you use it in the drying cycle. Change it with this replacement part.
This tumble dryer fluff filter is from AEG. You can also check other suitable brands from the list above.
Before ordering, please verify that this part is suitable for your model using our compatibility checker.
08
Customer Reviews (1)
5.01 review
5
1
4
0
3
0
2
0
1
0
Replacement filter
Ransom spares provided the exact part I needed. Their website was easy to use and the item was delivered quickly. I'll be using them in the future for any spares I need! Many thanks.
piers marson · woodbridge ·
Quality
Value
Ease of Fitting