Electrolux
Electrolux Dishwasher Heater & O-Ring Seal140002162232
Suitable for Electrolux, AEG, Arthur Martin, Atag, Dieter Knoll
Stock Code: 840518
£45.90inc. VAT
£38.25 ex. VAT
In Stock
Next Day Delivery Available
Moderate DIY repair
A confident home repairer can do this with basic tools.
01
Compatibility Check
02
What this part does
Heats the water as it circulates through the cycle.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| F8 | AEG | Means a heating fault, where the water is not reaching the required temperature in time. It is usually caused by a failure in the heating element, the NTC temperature sensor, or the control board. | High |
| E3 | Electrolux | Means the unit is taking too long to heat the water or is not heating at all. It is usually caused by a faulty heating element, a malfunctioning thermistor, or a wiring issue between the heating element and the main control board. | High |
| L1 | Electrolux | Means the rinse aid level is low, or on some models the water is not heating, or the door is not securely latched. It is usually caused by a low rinse aid level, a faulty heating element or thermostat, or an unlatched door. | Medium |
| AL7 | Zanussi | Means no water circulation has been detected. It is usually caused by a blocked filter, a blockage in the sink spigot, or a kinked or squashed drain hose. | Medium |
| E3 | Zanussi | Means the appliance has not reached the correct wash temperature, while on certain compact models it means excessive inlet water or a leak. It is usually caused by the heater, or on compact models overfilling or a drainage problem. | High |
F8High
AEG
Means a heating fault, where the water is not reaching the required temperature in time. It is usually caused by a failure in the heating element, the NTC temperature sensor, or the control board.
E3High
Electrolux
Means the unit is taking too long to heat the water or is not heating at all. It is usually caused by a faulty heating element, a malfunctioning thermistor, or a wiring issue between the heating element and the main control board.
L1Medium
Electrolux
Means the rinse aid level is low, or on some models the water is not heating, or the door is not securely latched. It is usually caused by a low rinse aid level, a faulty heating element or thermostat, or an unlatched door.
AL7Medium
Zanussi
Means no water circulation has been detected. It is usually caused by a blocked filter, a blockage in the sink spigot, or a kinked or squashed drain hose.
E3High
Zanussi
Means the appliance has not reached the correct wash temperature, while on certain compact models it means excessive inlet water or a leak. It is usually caused by the heater, or on compact models overfilling or a drainage problem.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
MediumGeneral fitting guidance. The exact steps can vary slightly with the make and model of your dishwasher.
Safety: Switch off and unplug at the mains before you start.
You’ll needScrewdriverPliers
- 1
- 2
- 3
- 4
- 5
- 6
06
Specifications
- Part Number
- 140002162232
- Alternative Part Numbers
- 140002162190
- Genuine Spare Part
- Yes
07
More Details
Genuine dishwasher heater and O-ring gasket seal to efficiently heat water and have secured seal when washing up. Able to withstand the high temperatures and water pressures while inside the dishwasher.
The heater warms the water in the dishwasher so it stays at the right temperature when it starts to clean your dishes. You have the O-ring seal so it’s leakproof between the heater and the dishwasher's plumbing.
When you replace the old heater, the O-ring seal might be worn out. So this set comes with a new O-ring seal.
This heater and O-ring seal is from Electrolux dishwashers but also fits other dishwasher brands like EG, Arthur Martin, Atag, Dishlex And Dishlex, Elektro Helios, Faure, Fors, Husqvarna, Husqvarna Electrolux, Ikea, John Lewis, Juno, Kuppersbusch, Leonard, Neue, Pelgrim, Progress, Rosenlew, Schulthess, Smeg, Zanker, Zanussi, and Zoppas.
Before ordering, please verify that this part is suitable for your model using our compatibility checker.
08
Customer Reviews (4)
5.04 reviews
5
4
4
0
3
0
2
0
1
0
Perfect part, dishwasher working perfectly
Takes a bit of time to fit but the identical part and the dishwasher now heating water as it should
Martin · Ipswich ·
Quality
Value
Ease of Fitting
Dishwasher heater
Perfect fit and easy to put on. Worth taking a photo of the old one in place, just to be sure...
Lee Foster · Chelmondiston ·
Quality
Value
Ease of Fitting
Great part not easy to fit
As stated great part, encountered problems not the fault of Ransom, just because the situation was difficult to assess. Good idea for the future and I know it would be a big job, but a how to section would put you so far ahead
Gerry Baylis · Little Eaton ·
Quality
Value
Ease of Fitting
heating element
Fast delivery and the part matched perfectly. Its been fitted almost two weeks without any issues. It resolved the lack of hot water during the wash cycle. I rubber elements were a little less rubbery than the original but it didn't cause me any concern.
michael · ENFIELD ·
Quality
Value
Ease of Fitting