Bosch
Bosch Dishwasher Fill Hose999067
Suitable for Bosch, Balay, Blaupunkt, Constructa, Gaggenau
Stock Code: 999067
£22.95inc. VAT
£19.13 ex. VAT
In Stock
Next Day Delivery Available
Moderate DIY repair
A confident home repairer can do this with basic tools.
01
Compatibility Check
02
What this part does
Brings the mains water into the dishwasher and shuts off if it detects a leak.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| E1 | Bosch | Means a water supply problem, a door latch fault, or a heat pump motor circuit fault at the main control board. It is usually caused by a faulty water inlet valve, drain pump, or main control board. | High |
| E14 | Bosch | Means the flow sensor or reed switch cannot detect water entering the machine. It is usually caused by a clogged inlet filter, low water pressure, or a faulty flow meter. | High |
| E16 | Bosch | Means a filling fault, where water cannot enter the machine or the water level is incorrect. It is usually caused by a clogged inlet filter, a kinked supply hose, or a faulty inlet valve. | High |
| E17 | Bosch | Means the machine is not filling with enough water or the flow rate is too low. It is usually caused by a kinked hose, a clogged inlet filter, low water pressure, or a faulty water inlet valve. | High |
| E18 | Bosch | Means the unit is not receiving enough water or the flow is too low. It is usually caused by a kinked inlet hose, a closed water tap, a clogged inlet filter, or a blockage in the drain pump. | High |
| E3 | Bosch | Means the dishwasher cannot fill with enough water within the allotted time. It is usually caused by a closed water tap, a blocked inlet hose, or a faulty inlet valve. | High |
| E5 | Bosch | Means the unit cannot fill with water properly or detect that it has, often stopping mid-cycle. It is usually caused by a filling problem or a fault in the main control board (power module or diverter circuit). | High |
| E8 | Bosch | Means the water level in the tub is too low, failing to rise above the heating element. It is usually caused by a clogged inlet filter, a faulty water inlet valve, or a defective flow sensor. | High |
| E14 | Neff | Means there is a water intake fault. It is usually caused by a faulty flow sensor, a stuck inlet valve, a leak activating the anti flood switch, a clogged inlet filter, or a kinked hose. | High |
| E15 | Neff | Means water has leaked into the base tray and triggered the anti flood safety switch, leaving the pump running continuously. It is usually caused by a failed sump seal, loose hoses, or a false alarm from suds. | High |
| E15 | Siemens | Means water has leaked into the base pan, triggering the anti-flood sensor and causing the drain pump to run continuously. It is usually caused by excessive suds, clogged filters, or a leaking hose. | High |
| E16 | Siemens | Means water is entering the water filling system uncontrollably or not at all. It is usually caused by a clogged filter, a faulty or stuck water inlet valve, or a kinked supply hose. | High |
| E17 | Siemens | Means the water flow rate is too high or the machine is overfilling. It is usually caused by high water pressure, a kinked inlet hose, a clogged filter in the AquaStop valve, or a malfunctioning flow sensor. | Medium |
| E32 | Siemens | Means the water level in the tub is too low. It is usually caused by blocked filters, kinked hoses, excessive suds, or dishes tipping over and collecting water. | Medium |
| E5 | Siemens | Means the water level in the unit is too low or the inlet valve is malfunctioning, and it appears on some models as a technical electronics error or a flood sensor issue. It is usually caused by a malfunctioning inlet valve or a water supply fault. | High |
| E8 | Siemens | Means the water level in the basin is too low. It is usually caused by a blocked filter, a faulty inlet valve, or obstructed spray arms. | Medium |
| E4 | Whirlpool | Means a water overflow or leak in the base pan has tripped the anti-flood float switch and shut the machine down, shown as F8E4. It is usually caused by an internal leak, a door not sealing, or a blocked filter. | Medium |
| E6 | Whirlpool | Means the unit detects no water, low water pressure, or incorrect water temperature, shown as F6E6. It is usually caused by a closed water tap, a kinked supply hose, a faulty water inlet valve, or a broken flow meter. | High |
| F5 | Whirlpool | Means a water detection or drainage fault has been detected. It is usually caused by a blocked filter, a faulty water inlet valve, a faulty float switch, or a rotor blocked in the wash motor. | High |
| F6 | Whirlpool | Means the unit is not receiving water or cannot detect it, shown as F6E1 or E1 F6. It is usually caused by a closed water supply valve, a kinked inlet hose, a faulty inlet valve, or a faulty flow meter. | High |
| H2 | Whirlpool | Means the dishwasher is not filling properly or cannot detect water entering the unit, shown as H2O. It is usually caused by a closed tap, a kinked inlet hose, or a blocked inlet screen. | High |
E1High
Bosch
Means a water supply problem, a door latch fault, or a heat pump motor circuit fault at the main control board. It is usually caused by a faulty water inlet valve, drain pump, or main control board.
E14High
Bosch
Means the flow sensor or reed switch cannot detect water entering the machine. It is usually caused by a clogged inlet filter, low water pressure, or a faulty flow meter.
E16High
Bosch
Means a filling fault, where water cannot enter the machine or the water level is incorrect. It is usually caused by a clogged inlet filter, a kinked supply hose, or a faulty inlet valve.
E17High
Bosch
Means the machine is not filling with enough water or the flow rate is too low. It is usually caused by a kinked hose, a clogged inlet filter, low water pressure, or a faulty water inlet valve.
E18High
Bosch
Means the unit is not receiving enough water or the flow is too low. It is usually caused by a kinked inlet hose, a closed water tap, a clogged inlet filter, or a blockage in the drain pump.
E3High
Bosch
Means the dishwasher cannot fill with enough water within the allotted time. It is usually caused by a closed water tap, a blocked inlet hose, or a faulty inlet valve.
E5High
Bosch
Means the unit cannot fill with water properly or detect that it has, often stopping mid-cycle. It is usually caused by a filling problem or a fault in the main control board (power module or diverter circuit).
E8High
Bosch
Means the water level in the tub is too low, failing to rise above the heating element. It is usually caused by a clogged inlet filter, a faulty water inlet valve, or a defective flow sensor.
E14High
Neff
Means there is a water intake fault. It is usually caused by a faulty flow sensor, a stuck inlet valve, a leak activating the anti flood switch, a clogged inlet filter, or a kinked hose.
E15High
Neff
Means water has leaked into the base tray and triggered the anti flood safety switch, leaving the pump running continuously. It is usually caused by a failed sump seal, loose hoses, or a false alarm from suds.
E15High
Siemens
Means water has leaked into the base pan, triggering the anti-flood sensor and causing the drain pump to run continuously. It is usually caused by excessive suds, clogged filters, or a leaking hose.
E16High
Siemens
Means water is entering the water filling system uncontrollably or not at all. It is usually caused by a clogged filter, a faulty or stuck water inlet valve, or a kinked supply hose.
E17Medium
Siemens
Means the water flow rate is too high or the machine is overfilling. It is usually caused by high water pressure, a kinked inlet hose, a clogged filter in the AquaStop valve, or a malfunctioning flow sensor.
E32Medium
Siemens
Means the water level in the tub is too low. It is usually caused by blocked filters, kinked hoses, excessive suds, or dishes tipping over and collecting water.
E5High
Siemens
Means the water level in the unit is too low or the inlet valve is malfunctioning, and it appears on some models as a technical electronics error or a flood sensor issue. It is usually caused by a malfunctioning inlet valve or a water supply fault.
E8Medium
Siemens
Means the water level in the basin is too low. It is usually caused by a blocked filter, a faulty inlet valve, or obstructed spray arms.
E4Medium
Whirlpool
Means a water overflow or leak in the base pan has tripped the anti-flood float switch and shut the machine down, shown as F8E4. It is usually caused by an internal leak, a door not sealing, or a blocked filter.
E6High
Whirlpool
Means the unit detects no water, low water pressure, or incorrect water temperature, shown as F6E6. It is usually caused by a closed water tap, a kinked supply hose, a faulty water inlet valve, or a broken flow meter.
F5High
Whirlpool
Means a water detection or drainage fault has been detected. It is usually caused by a blocked filter, a faulty water inlet valve, a faulty float switch, or a rotor blocked in the wash motor.
F6High
Whirlpool
Means the unit is not receiving water or cannot detect it, shown as F6E1 or E1 F6. It is usually caused by a closed water supply valve, a kinked inlet hose, a faulty inlet valve, or a faulty flow meter.
H2High
Whirlpool
Means the dishwasher is not filling properly or cannot detect water entering the unit, shown as H2O. It is usually caused by a closed tap, a kinked inlet hose, or a blocked inlet screen.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
MediumGeneral fitting guidance. The exact steps can vary slightly with the make and model of your dishwasher.
Safety: Switch off at the mains and turn off the water supply before you start.
You’ll needPliers
- 1
- 2
- 3
- 4
- 5
- 6
06
Specifications
- Part Number
- 999067
- Genuine Spare Part
- No
07
More Details
This is a high-quality dishwasher fill hose made of flexible plastic to withstand water pressure and movement. Measures 1.7 metres long.
Its long size means there's a longer reach to help dishwashers far from the main water source get their water supply.
Fill hoses are the ones supplying water to dishwashers. Has one end for the water supply and another for the inlet valve. Good fill hose for leak-free water flow.
This fill hose fits Balay, Blaupunkt, Bosch, Constructa, Gaggenau, Gorenje, Ikea, Junker, Koenic, Kuppersbusch, Neff, Pitsos, Profilo, Siemens, Viva, and Whirlpool dishwashers.
Before ordering, please verify with our compatibility checker that this part is suitable for your model.
08
Customer Reviews (3)
4.73 reviews
5
2
4
1
3
0
2
0
1
0
Very good product
Always best service from Ransom Spares. Can't fault it.
Rohinton Cooper · Stevenage ·
Quality
Value
Ease of Fitting
Great product,easy to fit
Performed as expected. Great value.I guess I have to write a minimum number of words
Philip White · Harmondsworth ·
Quality
Value
Ease of Fitting
Good value product
I needed a new water stop hose because the inlet connection brass thread insert had come loose. The replacement part was very easily located on the web site and it was most reassuring to be able to positively confirm that it would fit my Bosch dishwasher model. A lot of work has gone in to producing a comprehensive and easily navigated web site and it shows. The price was extremely competitive for a genuine Bosch part Delivery was quick, so all in all it was an excellent customer experience. Ransom spares is my first choice for domestic appliance spares.
Mr John William Shanahan · Middlesbrough ·
Quality
Value
Ease of Fitting