Electrolux
Electrolux Cooker & Hob 2400W Fan Oven Element140089339059
Suitable for Electrolux, AEG, Arthur Martin, Atag, Dieter Knoll
Stock Code: 652514
£24.50inc. VAT
£20.42 ex. VAT
In Stock
Next Day Delivery Available
Moderate DIY repair
A confident home repairer can do this with basic tools.
01
Compatibility Check
02
What this part does
Generates the heat that the fan circulates around the oven.
03
Will this fix my appliance?
Tick the symptoms your appliance is showing. We’ll tell you how confident we are this part is the fix.
04
Error codes related to this part
Error codes are model dependent, so the same brand may have more than one listed.
| Code | Brand | What it means | Confidence |
|---|---|---|---|
| F10 | AEG | Means a runaway temperature fault, where the oven has overheated or the control board has read an out of range temperature. It is usually caused by a faulty temperature sensor, a defective control board with a stuck relay, or a wiring fault. | Medium |
| F17 | AEG | Means a communication failure between the induction hob and the main oven control board, or a faulty temperature sensor or NTC thermistor. It is usually caused by a fault in the induction generator, sensor, or control board. | Medium |
| F10 | Electrolux | Means the oven temperature is running away, with the oven overheating or the sensor reading excessive heat often above 500F. It is usually caused by a defective temperature sensor (thermistor) or a faulty main control board. | Medium |
| F131 | Zanussi | Means the steamer sensor temperature is too high on steam-assisted models, triggering a safety alert. It is usually caused by the steamer sensor or control board. | Medium |
F10Medium
AEG
Means a runaway temperature fault, where the oven has overheated or the control board has read an out of range temperature. It is usually caused by a faulty temperature sensor, a defective control board with a stuck relay, or a wiring fault.
F17Medium
AEG
Means a communication failure between the induction hob and the main oven control board, or a faulty temperature sensor or NTC thermistor. It is usually caused by a fault in the induction generator, sensor, or control board.
F10Medium
Electrolux
Means the oven temperature is running away, with the oven overheating or the sensor reading excessive heat often above 500F. It is usually caused by a defective temperature sensor (thermistor) or a faulty main control board.
F131Medium
Zanussi
Means the steamer sensor temperature is too high on steam-assisted models, triggering a safety alert. It is usually caused by the steamer sensor or control board.
Don’t see your code? Different model years sometimes use different codes. Get in touch with our parts team and we’ll help you identify the right replacement.
05
Fitting Guidance
MediumGeneral fitting guidance. The exact steps can vary slightly with the make and model of your cooker.
Safety: Switch off and unplug at the mains and let it cool before you start.
You’ll needScrewdriverNut driver
- 1
- 2
- 3
- 4
- 5
- 6
- 7
06
Specifications
- Part Number
- 140089339059
- Alternative Part Numbers
- 3878684004, 3878684103
- EAN / Barcode
- 7321422007174
- Genuine Spare Part
- Yes
- Fan Oven Element
- 2400w
07
More Details
This fan oven element is a genuine replacement part. It is a 2400w element and is a 2 ring design.
When an oven element is faulty it will normally mean that your oven is no longer getting hot.
This replacement oven element fit select models of the brands listed above. Please make sure that you check suitability for you model before ordering using our compatibility checker.
If you need help in fitting this genuine part check out our DIY help video below.
Safety Warning - Always unplug from the mains before carrying out any repairs.
- Oven model used - Hotpoint DU2540WH
- Part number used - RS8443
08
Video
Please note that the following video will give you a guide on how to fit this part, however the exact fitting may differ depending on your make and model.
Need to find a specific part of the video? Use the timestamps below...
- 0:21 - Taking the oven door off
- 0:37 - Removing backplate
- 0:46 - Removing oven element
- 1:09 - Installing new oven element
- 1:41 - Putting oven door back on
09
Customer Reviews (48)
4.948 reviews
5
45
4
3
3
0
2
0
1
0
Sort by:||
Great product, easy to fit.
Genuine Zanussi element at a lower price than Zanussi direct. Website enabled me to locate and order the correct part. Incredibly easy to fit.
Mark Gordon · Cambridge ·
Quality
Value
Ease of Fitting
Good element, simple fitting, fast delivery
Genuine part AEG element, well packaged and arrived swiftly after ordering. No problems fitting and works perfectly. Thanks Ransom!
Will C · Oswestry ·
Quality
Value
Ease of Fitting
Great value product, arrived quickly
Great facility on the website to check the part will fit your appliance. Excellent quality product, delivered very quickly. Saved me hundreds in repair bills.
Chantal John · Hereford ·
Quality
Value
Ease of Fitting
Great service
The replacement product was easy to source on the website. Ordering was simple and efficient. The product cost was as expected. Shipping was very good and product arrived as expected. Easy to fit and now works perfectly.
Brian A · Chester ·
Quality
Value
Ease of Fitting
perfect spare part
arrived on time perfect fit works 100% would trade with again
martin · boston ·
Quality
Value
Ease of Fitting