Will This Part Fit My Appliance?

Choose your brand from the list below to check your model compatibility.

Start typing your model number below to check compatibility.

Description

What is the function of the switch assembly in cooker hoods?

The switch assembly in cooker hoods serves as the control mechanism for operating various functions of the hood, such as turning on/off the fan and lights. It allows users to adjust the fan speed and control the illumination level, providing convenience and customization in the kitchen ventilation process.

When does it get damaged?

The switch assembly gets damaged due to wear and tear over time, frequent usage, electrical issues, or exposure to moisture and grease. Common signs of damage include unresponsiveness to commands, flickering lights, or difficulty in adjusting fan speeds.

Would this fit in my cooker hood?

This switch assembly fits Hygena and Diplomat cooker hoods. Use our compatibility checker to see if this part fits your model.

Manufacturers Part Number:

  • W0000051

Alternative Part Numbers:

  1. HY-012
  2. Y012

Will this part fit your appliance?

Use our compatibility checker, Click here.

Finding your model number:

Struggling to find the model number on your Cooker Hood? Click here.

Safety note:

Warning: Always unplug any appliance from the electricity supply before carrying out any work or testing on it.

Latest Product Review(s)

Read All Reviews
24 Customer Review(s)

Good product

I used an electrician to fit this part and it took him a while to fit. I suggested he read the reviews beforehand but he didn't, then found he had to go back and get his soldering kit. Pleased with the job and product in the end.

By Pauline English - King's Lynn
23rd Aug 2023

Overall

Quality

Value

Ease of Fitting

PCB switch assembly

I found this swich assembly so easy to fit, as long as you are able to resolder the wiring. Refit the wiring one wire at a time, bare back the insulation to a new bit (approx. 5mm) keeping the new end clean. Resolder the new wiring ends after tinning the copper end of the newly bared wire end. Do all the work with the old switch in situ. so you won't mix up the wiring. An electric soldering iron and multicore solder are a must have, nothing else will do.

By Mr A Smith - Banchory, Scotland.
13th Mar 2023

Overall

Quality

Value

Ease of Fitting

Product as described, fairly tricky to fit , soldering iron required

New board requires soldering onto existing wiring in situ, would be easier if the board came with wires pre soldered which could then be connected to existing feed wires.

By Steve Mills - Bolton
4th Mar 2023

Overall

Quality

Value

Ease of Fitting

Very pleased

I am so pleased to have found this part via Ransom Spares. A bit of soldering and it's saved me the bother of drilling and fixing a new cooker hood into place. Very pleased.

By Peter Osborne - Cwmbran
11th May 2022

Overall

Quality

Value

Ease of Fitting

Cooker hood pcb

Bought this PCB and it's good quality and quick delivery. Thanks

By Muhammad Fayaz - Crawley
22nd Apr 2022

Overall

Quality

Value

Ease of Fitting

Easy to fit

Easy to fit all you need was a screwdriver and soldering iron flux and solder

By R A Hayes - Merseyside
22nd Nov 2021

Overall

Quality

Value

Ease of Fitting

Does what it says

I ordered this and received it in the post promptly as promised. Fitting was fiddly due to the design of the cooker hood. It required the use of a soldering iron as I had seen mentioned in other reviews, so was not as easy to fit as if it had screws. But that was not the end of the world. I have been using it now for two weeks and it all seems to be working fine. One suggestion for those less confident, is to take picture of the installed unit BEFORE you replace it. There are several wires and it IS easy to mix them. Now I need to replace one of the light fittings that has also failed. My only complaint is the cost, which is high for what it is.

By Donald Page - Eye
1st Jun 2021

Overall

Quality

Value

Ease of Fitting

Great product

It was easy to fit and arrived on time. Very good quality product. It could be a little cheaper.

By Vishal Gohil - Leicester
30th Mar 2021

Overall

Quality

Value

Ease of Fitting

Easy to fit

I thought I needed to buy a new cooker hood then someone told me I could get a new switch unit so I googled it found Ransoms and hey presto it was about 30 quid instead of 150 quite simple to fit with a bit of basic soldering so I would recommend it

By Anthony Taylor - Sutton Surrey
29th Mar 2021

Overall

Quality

Value

Ease of Fitting

Unfortunately the wrong part

The repair firm I hired said the part was for a newer model of cooker hood and they couldn't fit it. Not sure how hard they tried. Disappointed but can't really fault Ransome. They sent the part promptly. If Ransome could contact me to see if we can track down the right part that would be great.

By John Anthony Sexton - SCARBOROUGH
22nd Sep 2020

Overall

Quality

Value

Ease of Fitting

Load More Reviews

Questions And Answers

1 Answer(s)
Please can you tell me if the electrical cable black on one side white on the other? Thank you
By Carolyn - Swansea - 10/11/2019
Hi Carolyn, thanks for your question. This PCB comes without the cables, so you'd need to solder the original cables to the board.
By Jordan - Staff Member
1 Answer(s)
Hi folks, does this come with the push in buttons or do we use the old buttons.
By Dorothy - Edinburgh - 12/04/2020
Hi Dorothy, the switches are included but the push buttons are a separate part.
By Jordan - Staff Member
1 Answer(s)
I just see the PCB container, I don't see the switches. Is there a board included?
By Bob - Worcester - 20/04/2020
Hi Bob, I can confirm the board and switches are included in this.
By Jordan - Staff Member
1 Answer(s)
hi. Are there 6 screw positions on the bottom of control box (not visible in piture), 4 screws holding the unit together, 2 positions to attach the metal bracket so it can be secured in the front of the hood. Cheers
By Atvinder - Bedford - 15/05/2020
Hi Atvinder, I can confirm this is held together with 4 screws, but it doesn't seem to have 2 positions for the bracket.
By Jordan - Staff Member
1 Answer(s)
Has anyone fitted this to Hygena APP2440 as it cannot be confirmed that it will fit.
By Barbara - High Wycombe - 02/02/2021
Hi Barbara, I can confirm this is the correct PCB for your model.
By Jordan - Staff Member

Be the first to ask a question for this product.

Ask a new question

Customers Also Viewed